Whatever language you listen to music in, we know you prefer it as intererfence free as possible. You need theĀ Gemini3.0Ā dual-headed cable.
In most mass-produced USB cables, the signal and power cables are normally compacted together. This means two things ā poor conductivity and they are not protected from one another.
This leads to interference and degrades quality.
TheĀ Gemini3.0Ā cable carries the audio signal and power in two separate cables.
This separates the delicate USB data signal from the USB power.
No interference and sound quality remains unaffected.
We strictly adhere to the usb.orgĀ specifications. A key factor that is often overlooked is sticking to the 90 ohms impedance. This is achieved using the following exhaustive methods.
We use heavy OFHC continuous copper silver matrix conductors for the best possible signal transfer. The cable construction is a custom minimum inductance parallel type with dual shielding. This protects the cable from RFI and EMIĀ noise and provides the cleanest transfer medium possible.
With the machined FINAL connectors and atypical RF3 filter designs, the iFiĀ Gemini3.0Ā sets a whole new sonic benchmark for computer audio transmission.
The signal runs through the cable and the connector. This means the connector too must be exceptional.
Most USB cables use moulded plastic covered connections that do not shield the high frequencies present in the USB data link. Noise radiates out. Very few make their own connectors and rely on off-the-shelf components. These often lack durability.
Our FINAL USB connectors provide impeccable end-to-end RF shielding. They are machined entirely from solid, aircraft-grade aluminium. Plus their gold-plated connections make for years of steadfast service.
The power cable is heavier gauge than often found in standard USB cables. And signal and ground have their own respective geometry for optimal conductivity.
There are dual-headed designs and then there is theĀ Gemini3.0Ā dual headed design. Nothing comes close.
Few manufacturers make their own final connectors.
Most USB cables use moulded plastic covered connections that do not shield the high frequencies present in the USB data link. Noise leaks out and durability is compromised.
Our iFi FINAL USB connectors provide impeccable end-to-end RF shielding, being machined entirely from solid, aircraft-grade aluminium. Plus gold-plated connections make for years of steadfast service.
USB3.0ās ultra-speed bandwidth of 5.0Gbps offers an incredibly wide bandwidth, 10x that of USB2.0ās 480Mbps.
With generic mass-produced USB cables, the data and power cables are normally packed together. This means that they do not conduct as well as they should and they are not sufficiently shielded from each other. This has a negative impact on USB signal integrity and degrades sound quality.
Our quadruple shielding fully separates and protects the delicate USB data signal from the power. This protects the cable from RFI and EMI noise to provide the cleanest transfer medium possible.
Most standard USB cables do not address RF issues and are fitted with filters that work over too narrow a range and are only fitted at the ends of the cables, leaving the length of the cable to act as an antennae.
iFiās three custom-made metal oxide ceramic filters have a different effective range to broaden the range over which RF noise is silenced. The middle silencer is adjustable and can be moved along the whole length of the cable. This then ādetunesā the antennae formed by the cable. The other two silencers should be kept as close to each respective end as possible.
Original: $79.00
-65%$79.00
$27.65
Whatever language you listen to music in, we know you prefer it as intererfence free as possible. You need theĀ Gemini3.0Ā dual-headed cable.
In most mass-produced USB cables, the signal and power cables are normally compacted together. This means two things ā poor conductivity and they are not protected from one another.
This leads to interference and degrades quality.
TheĀ Gemini3.0Ā cable carries the audio signal and power in two separate cables.
This separates the delicate USB data signal from the USB power.
No interference and sound quality remains unaffected.
We strictly adhere to the usb.orgĀ specifications. A key factor that is often overlooked is sticking to the 90 ohms impedance. This is achieved using the following exhaustive methods.
We use heavy OFHC continuous copper silver matrix conductors for the best possible signal transfer. The cable construction is a custom minimum inductance parallel type with dual shielding. This protects the cable from RFI and EMIĀ noise and provides the cleanest transfer medium possible.
With the machined FINAL connectors and atypical RF3 filter designs, the iFiĀ Gemini3.0Ā sets a whole new sonic benchmark for computer audio transmission.
The signal runs through the cable and the connector. This means the connector too must be exceptional.
Most USB cables use moulded plastic covered connections that do not shield the high frequencies present in the USB data link. Noise radiates out. Very few make their own connectors and rely on off-the-shelf components. These often lack durability.
Our FINAL USB connectors provide impeccable end-to-end RF shielding. They are machined entirely from solid, aircraft-grade aluminium. Plus their gold-plated connections make for years of steadfast service.
The power cable is heavier gauge than often found in standard USB cables. And signal and ground have their own respective geometry for optimal conductivity.
There are dual-headed designs and then there is theĀ Gemini3.0Ā dual headed design. Nothing comes close.
Few manufacturers make their own final connectors.
Most USB cables use moulded plastic covered connections that do not shield the high frequencies present in the USB data link. Noise leaks out and durability is compromised.
Our iFi FINAL USB connectors provide impeccable end-to-end RF shielding, being machined entirely from solid, aircraft-grade aluminium. Plus gold-plated connections make for years of steadfast service.
USB3.0ās ultra-speed bandwidth of 5.0Gbps offers an incredibly wide bandwidth, 10x that of USB2.0ās 480Mbps.
With generic mass-produced USB cables, the data and power cables are normally packed together. This means that they do not conduct as well as they should and they are not sufficiently shielded from each other. This has a negative impact on USB signal integrity and degrades sound quality.
Our quadruple shielding fully separates and protects the delicate USB data signal from the power. This protects the cable from RFI and EMI noise to provide the cleanest transfer medium possible.
Most standard USB cables do not address RF issues and are fitted with filters that work over too narrow a range and are only fitted at the ends of the cables, leaving the length of the cable to act as an antennae.
iFiās three custom-made metal oxide ceramic filters have a different effective range to broaden the range over which RF noise is silenced. The middle silencer is adjustable and can be moved along the whole length of the cable. This then ādetunesā the antennae formed by the cable. The other two silencers should be kept as close to each respective end as possible.
Product Information
Shipping & Returns
Whatever language you listen to music in, we know you prefer it as intererfence free as possible. You need theĀ Gemini3.0Ā dual-headed cable.
In most mass-produced USB cables, the signal and power cables are normally compacted together. This means two things ā poor conductivity and they are not protected from one another.
This leads to interference and degrades quality.
TheĀ Gemini3.0Ā cable carries the audio signal and power in two separate cables.
This separates the delicate USB data signal from the USB power.
No interference and sound quality remains unaffected.
We strictly adhere to the usb.orgĀ specifications. A key factor that is often overlooked is sticking to the 90 ohms impedance. This is achieved using the following exhaustive methods.
We use heavy OFHC continuous copper silver matrix conductors for the best possible signal transfer. The cable construction is a custom minimum inductance parallel type with dual shielding. This protects the cable from RFI and EMIĀ noise and provides the cleanest transfer medium possible.
With the machined FINAL connectors and atypical RF3 filter designs, the iFiĀ Gemini3.0Ā sets a whole new sonic benchmark for computer audio transmission.
The signal runs through the cable and the connector. This means the connector too must be exceptional.
Most USB cables use moulded plastic covered connections that do not shield the high frequencies present in the USB data link. Noise radiates out. Very few make their own connectors and rely on off-the-shelf components. These often lack durability.
Our FINAL USB connectors provide impeccable end-to-end RF shielding. They are machined entirely from solid, aircraft-grade aluminium. Plus their gold-plated connections make for years of steadfast service.
The power cable is heavier gauge than often found in standard USB cables. And signal and ground have their own respective geometry for optimal conductivity.
There are dual-headed designs and then there is theĀ Gemini3.0Ā dual headed design. Nothing comes close.
Few manufacturers make their own final connectors.
Most USB cables use moulded plastic covered connections that do not shield the high frequencies present in the USB data link. Noise leaks out and durability is compromised.
Our iFi FINAL USB connectors provide impeccable end-to-end RF shielding, being machined entirely from solid, aircraft-grade aluminium. Plus gold-plated connections make for years of steadfast service.
USB3.0ās ultra-speed bandwidth of 5.0Gbps offers an incredibly wide bandwidth, 10x that of USB2.0ās 480Mbps.
With generic mass-produced USB cables, the data and power cables are normally packed together. This means that they do not conduct as well as they should and they are not sufficiently shielded from each other. This has a negative impact on USB signal integrity and degrades sound quality.
Our quadruple shielding fully separates and protects the delicate USB data signal from the power. This protects the cable from RFI and EMI noise to provide the cleanest transfer medium possible.
Most standard USB cables do not address RF issues and are fitted with filters that work over too narrow a range and are only fitted at the ends of the cables, leaving the length of the cable to act as an antennae.
iFiās three custom-made metal oxide ceramic filters have a different effective range to broaden the range over which RF noise is silenced. The middle silencer is adjustable and can be moved along the whole length of the cable. This then ādetunesā the antennae formed by the cable. The other two silencers should be kept as close to each respective end as possible.
Original: $79.00
-65%$79.00
$27.65
